TPM Wash Solvent | 5L compensates CO2-Emissions equal to 10 times its weight learn more at

Product information "TPM Wash Solvent | 5L"

TPM Wash Solvent (Tripropylenglykolmonomethylether) is a non-flammable, low odour solvent that can be used to clean and dissolve uncured resin on stereolithography (SLA) 3D printed parts. TPM has a lower evaporation rate than IPA and washes about three times as many parts as IPA before needing to be replaced.

TPM is not currently certified for use with Formlabs biocompatible resins.

TPM is compatible with the Formlabs Finish Kit, Form Wash, and Form Cure.
For a detailed workflow, visit


Always wear gloves when handling TPM.

For removing uncured Resin from SLA or DLP printed parts fill your cleaning vessel with the amount specified by the manufacturer. To minimize waste, it's suggested to pre-clean the parts before placing them in the cleaning vessel to expand the lifespan of your fresh TPM. This can be done in a separate container with either "dirty" TPM from previous cleaning cycles or low evaporation cleaners such as DPM, TPM or PGDA. Place the finished print in the cleaning vessel and clean the parts for at least 5 min. or according to the material manufacturers guidelines. After the cleaning cycle, wash the DPM coated part with water, let the model dry and check for a tacky surface, repeat if necessary, till the surface is not tacky anymore. If it's still tacky replace the TPM.

Advantages of TPM Wash Solvent

  • TPM is able to disolve up to 4 times as much resin as IPA
  • The evaportaion rate of TPM is much slower making it easy to store without loosing much of the product
  • Almost Oderless to a slight chemical smell makes working with TPM easier on the people in contact
  • Not Labeled as a dangerous good with no special requirements regarding storage, ventilation or flame hazard makes TPM Wash solvent the perfect indoor, office, Laboratory Solvent


  • Formlabs Wash
  • Formlabs Wash L
Not Compatible
  • Formlabs Biocompatible Resin - Use IPA

Disposal of TPM Wash Solvent

TPM and container as well as rinsing water need to be disposed of at an appropriate waste treatment site.

Labeling according to Regulation (EG) Nr. 1272/2008 (CLP)

This product is not labeled as dangerous.

General precautions
  • Keep out of reach of children.
  • Avoid breathing dust/fume/gas/mist/vapours/spray.
  • IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
  • Store in a well-ventilated place. Keep container tightly closed.
  • Dispose of contents/container in accordance with local regulations.
Technical Data
Purity >99%
Chemical name Tripropylene glycol monomethyl ether
CAS Number 25498-49-1
Gravity 0.96g/cm³ (25°C)
VOC 0g/L
Supplemental Information
HS Code 2909 4980
Country of Origin Austria
Product Weight 4,8kg
Shipping Weight 5,2kg
Packaging Dimensions (5L) 18,2 x 16,2 x 24,5cm
Shipping Restrictions None
GTIN/EAN 9120078083604
Dental: No

0 of 0 reviews

Write a review

Share your experiences with other customers.

Canister Key | 51mm
Canister Key 51mm width. Helpful for easy opening and closing of the 5L canisters. Packaging Content 1x Canister Key 51mm
Single Use Nitrile Gloves | 100 pcs - Size L
Packaging Units: 1 | Size: L
Disposable nitrile gloves are free of allergy-causing proteins and are therefore a skin-friendly alternative to latex gloves. Nitrile gloves are resistant to many chemicals and oils, are tear-resistant, convince with their high elasticity and convey a good sense of touch. They are ideal for use in medicine, nursing and home care. Nitrile gloves are food safe, which makes them the first choice in the food industry & food processing. Test parameters Test criteria Test level AQL Dimensions S-2 4.0 Physical properties S-2 4.0 1000ml water tightness test G-1 1.5 Visual inspection for minor defects G-1 4.0 Technical data Material: nitrile Color: Black Length 240mm, width: 105 +/- 5mm Standards: food safe, CE, EN 374, EN 455, T. 1-4 Disposal of disposable gloves Depending on the product used, gloves must be disposed of accordingly.
Resin Filter | 25x
Content: 25
Resin filter are paper funnel with integrated 125μm mesh to filter cured particles from resin. Application for removing cured resin particle Wear gloves when handling resin. If available, place Resin bottle on a silicone mat and use a PP funnel to stable the filter. Pour the resin slowly from the resin tank of the 3D printer through the filter into the bottle. Resin should be filtered as a general maintainance, especially after a failed print to remove loose particles. Disposal To dispose of used resin filter  Let the resin cure under UV light. Dispose of fully cured resin filter is possible through household waste. Packaging Content 1x Box with 25 Resin filter

Variants from US$5.41*